[[TitleIndustry]]

DIN 908 pdf standard screw plug

Date:Jun 06, 2019


DIN 908 is Internal drive screw plugs with collar - Cylindrical thread


DIN 908 stainless steel material, M 16 thread tightening torque data and ISO equivalent.

DIN_908_size_screw_plug_standard

DIN 908 standard specifies dimensions, masses and technical delivery conditions for screw plugs which are intended to be screwed into holes with parallel thread as specified in DIN 13-5, DIN 13-6 or DIN 13-7, and DIN EN ISO 228-1.


Such plugs may be used together with seal rings as specified in DIN 7603, the type and material of which are to be selected as a function of the operating conditions (e.g. the fluid with which the threaded parts are in contact, temperature, pressure, etc.).


Standard references as follow:

DIN 13-7 : 1999 ISO GENERAL PURPOSE METRIC SCREW THREADS - PART 7: NOMINAL SIZES FOR 2 MM FINE PITCH THREADS - NOMINAL DIAMETER FROM 17 MM TO 300 MM

DIN EN 10087 : 1999 FREE-CUTTING STEELS - TECHNICAL DELIVERY CONDITIONS FOR SEMI-FINISHED PRODUCTS, HOT ROLLED BARS AND RODS

DIN 5586 : 1989 COMPRESSED AIR EQUIPMENT FOR RAIL VEHICLES - LOCKING SCREWS WITH COLLAR AND VENT

DIN ISO 8992 : 2005 FASTENERS; GENERAL REQUIREMENTS FOR BOLTS, SCREWS, STUDS AND NUTS

DIN EN 10277-3 : 2008 BRIGHT STEEL PRODUCTS - TECHNICAL DELIVERY CONDITIONS - PART 3: FREE-CUTTING STEELS

DIN EN 28839 : 1991 MECHANICAL PROPERTIES OF FASTENERS - BOLTS, SCREWS STUDS AND NUTS MADE OF NON-FERROUS METALS

DIN EN ISO 3269 : 2000 FASTENERS - ACCEPTANCE INSPECTION

DIN EN ISO 4759-1 : 2001 TOLERANCES FOR FASTENERS - PART 1: BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C

DIN 909 : 2012 HEXAGON HEAD PIPE PLUGS - CONICAL THREAD

DIN EN 26157-3 : 1991 FASTENERS - SURFACE DISCONTINUITIES - BOLTS, SCREWS AND STUDS SUBJECT FOR SPECIAL REQUIREMENTS

DIN 7603 : 2001 SEALING RINGS

DIN 3852-1 : 2014 STUD ENDS AND PORTS OF FITTINGS, VALVES AND PLUG SCREWS - PART 1: DIMENSIONS FOR METRIC FINE PITCH THREAD

DIN 13-5 : 1999 ISO GENERAL PURPOSE METRIC SCREW THREADS - PART 5: NOMINAL SIZES FOR 1 MM AND 1,25 MM FINE PITCH THREADS - NOMINAL DIAMETER FROM 7,5 MM TO 200 MM

DIN EN ISO 3506-1 : 2010 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 1: BOLTS, SCREWS AND STUDS

DIN EN ISO 3506-3 : 2010 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 3: SET SCREW AND SIMILAR FASTENERS NOT UNDER TENSILE STRESS

ISO 9974-4 : 2016 CONNECTIONS FOR GENERAL USE AND FLUID POWER - PORTS AND STUD ENDS WITH ISO 261 THREADS WITH ELASTOMERIC OR METAL-TO-METAL SEALING - PART 4: DIMENSIONS, DESIGN, TEST METHODS AND REQUIREMENTS FOR EXTERNAL HEX AND INTERNAL HEX PORT PLUGS

DIN EN ISO 225 : 2011 FASTENERS - BOLTS, SCREWS, STUDS AND NUTS - SYMBOLS AND DESCRIPTIONS OF DIMENSIONS

DIN 267-2 : 2016 FASTENERS - TECHNICAL SPECIFICATION, SURFACE ROUGHNESS FOR PRODUCT CLASSES A AND B

DIN EN ISO 10664 : 2015 HEXALOBULAR INTERNAL DRIVING FEATURE FOR BOLTS AND SCREWS (ISO 10664:2014)

DIN EN ISO 228-1 : 2003 PIPE THREADS WHERE PRESSURE-TIGHT JOINTS ARE NOT MADE ON THE THREADS - PART 1: DIMENSIONS, TOLERANCES AND DESIGNATION

DIN 910 : 2012 HEXAGON HEAD SCREW PLUGS WITH COLLAR - CYLINDRICAL THREAD

DIN EN ISO 3506-2 : 2010 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS

DIN ISO 965-1 : 2017 ISO GENERAL PURPOSE METRIC SCREW THREADS - TOLERANCES - PART 1: PRINCIPLES AND BASIC DATA (ISO 965-1:2013)

DIN ISO 2768-1 : 1991 GENERAL TOLERANCES - TOLERANCES FOR LINEAR AND ANGULAR DIMENSIONS WITHOUT INDIVIDUAL TOLERANCE INDICATIONS

DIN EN 10263-2 : 2014 STEEL ROD, BARS AND WIRE FOR COLD HEADING AND COLD EXTRUSION - PART 2: TECHNICAL DELIVERY CONDITIONS FOR STEELS NOT INTENDED FOR HEAT TREATMENT AFTER COLD WORKING

DIN EN ISO 4042 : 2001 FASTENERS - ELECTROPLATED COATINGS

DIN 962 : 2013 BOLTS, SCREWS, STUDS AND NUTS - DESIGNATIONS, TYPES AND FINISHES

DIN 7604 : 2016 HEXAGON HEAD SCREW PLUGS - LIGHT TYPE - CYLINDRICAL THREAD

DIN EN ISO 10683 : 2016 FASTENERS - NON-ELECTROLYTICALLY APPLIED ZINC FLAKE COATINGS (ISO 10683:2014)

DIN 13-6 : 1999 ISO GENERAL PURPOSE METRIC SCREW THREADS - PART 6: NOMINAL SIZES FOR 1,5 MM FINE PITCH THREADS - NOMINAL DIAMETER FROM 12 MM TO 300 MM

DIN 3852-2 : 2014 STUD ENDS AND PORTS OF FITTINGS, VALVES AND PLUG SCREWS - PART 2: DIMENSIONS FOR PIPE THREAD

DIN 34824 : 2007 12 POINT SOCKET FOR BOLTS AND SCREWS

DIN 906 : 2012 INTERNAL DRIVE PIPE PLUGS - CONICAL THREAD



Previous: DIN 910 pdf size chart screw plug

Next: DIN 906 pdf specification standard