DIN 7604 form a c plug dimension

Date:Jun 06, 2019

DIN 7604 is Hexagon head screw plugs - Light type - Cylindrical thread

DIN 7604  standard specifies requirements for screw plugs which are intended to be screwed into holes with parallel thread as specified in DIN 13-5 or DIN 13-6. Such plugs are used together with a suitable seal ring, the type and material of which are to be selected as a function of the operating conditions (e.g. the medium, temperature, pressure, etc.).

NOTE In deviation from the specifications of this standard, if screw plugs are intended to be used without a seal ring it is recommended that a Type B stud end according to DIN 3852-1 should be used.

Standards Referencing This Book:

DIN EN 10087 : 1999 FREE-CUTTING STEELS - TECHNICAL DELIVERY CONDITIONS FOR SEMI-FINISHED PRODUCTS, HOT ROLLED BARS AND RODS

DIN 5586 : 1989 COMPRESSED AIR EQUIPMENT FOR RAIL VEHICLES - LOCKING SCREWS WITH COLLAR AND VENT

DIN ISO 8992 : 2005 FASTENERS; GENERAL REQUIREMENTS FOR BOLTS, SCREWS, STUDS AND NUTS

DIN 908 : 2012 INTERNAL DRIVE SCREW PLUGS WITH COLLAR - CYLINDRICAL THREAD

DIN EN 10277-3 : 2008 BRIGHT STEEL PRODUCTS - TECHNICAL DELIVERY CONDITIONS - PART 3: FREE-CUTTING STEELS

DIN EN 28839 : 1991 MECHANICAL PROPERTIES OF FASTENERS - BOLTS, SCREWS STUDS AND NUTS MADE OF NON-FERROUS METALS

DIN EN ISO 3269 : 2000 FASTENERS - ACCEPTANCE INSPECTION

DIN EN ISO 4759-1 : 2001 TOLERANCES FOR FASTENERS - PART 1: BOLTS, SCREWS, STUDS AND NUTS - PRODUCT GRADES A, B AND C

DIN 909 : 2012 HEXAGON HEAD PIPE PLUGS - CONICAL THREAD

DIN EN 26157-3 : 1991 FASTENERS - SURFACE DISCONTINUITIES - BOLTS, SCREWS AND STUDS SUBJECT FOR SPECIAL REQUIREMENTS

DIN 475-1 : 2015 WIDTHS ACROSS FLATS FOR BOLTS, SCREWS, VALVES AND FITTINGS

DIN 3852-1 : 2014 STUD ENDS AND PORTS OF FITTINGS, VALVES AND PLUG SCREWS - PART 1: DIMENSIONS FOR METRIC FINE PITCH THREAD

DIN EN ISO 16048 : 2003 PASSIVATION OF CORROSION-RESISTANT STAINLESS-STEEL FASTENERS

DIN EN ISO 3506-1 : 2010 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 1: BOLTS, SCREWS AND STUDS

DIN EN ISO 3506-3 : 2010 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 3: SET SCREW AND SIMILAR FASTENERS NOT UNDER TENSILE STRESS

DIN EN ISO 225 : 2011 FASTENERS - BOLTS, SCREWS, STUDS AND NUTS - SYMBOLS AND DESCRIPTIONS OF DIMENSIONS

DIN 910 : 2012 HEXAGON HEAD SCREW PLUGS WITH COLLAR - CYLINDRICAL THREAD

DIN EN ISO 3506-2 : 2010 MECHANICAL PROPERTIES OF CORROSION-RESISTANT STAINLESS STEEL FASTENERS - PART 2: NUTS

DIN ISO 965-1 : 2017 ISO GENERAL PURPOSE METRIC SCREW THREADS - TOLERANCES - PART 1: PRINCIPLES AND BASIC DATA (ISO 965-1:2013)

DIN ISO 2768-1 : 1991 GENERAL TOLERANCES - TOLERANCES FOR LINEAR AND ANGULAR DIMENSIONS WITHOUT INDIVIDUAL TOLERANCE INDICATIONS

DIN EN 10263-2 : 2014 STEEL ROD, BARS AND WIRE FOR COLD HEADING AND COLD EXTRUSION - PART 2: TECHNICAL DELIVERY CONDITIONS FOR STEELS NOT INTENDED FOR HEAT TREATMENT AFTER COLD WORKING

DIN EN ISO 4042 : 2001 FASTENERS - ELECTROPLATED COATINGS

DIN 962 : 2013 BOLTS, SCREWS, STUDS AND NUTS - DESIGNATIONS, TYPES AND FINISHES

DIN EN ISO 9717 : 2016 METALLIC AND OTHER INORGANIC COATINGS - PHOSPHATE CONVERSION COATING OF METALS (ISO 9717:2017)

DIN ISO 272 : 1979 FASTENERS; WIDTH ACROSS FLATS FOR HEXAGON PRODUCTS

DIN EN ISO 10683 : 2016 FASTENERS - NON-ELECTROLYTICALLY APPLIED ZINC FLAKE COATINGS (ISO 10683:2014)

DIN 906 : 2012 INTERNAL DRIVE PIPE PLUGS - CONICAL THREAD